- Privacy Policy
- Cookie Policy
- KVKK
*Pinhole Opening and Closing will be with automatic reducer motor.
*Pinhole opening and closing motor will be AC 0.25kW.
*Pinhole opening and closing reducer will be yılmaz reducer.
*Reel lowering and lifting will be automatic reducer motorized.
*The reel lowering lifting motor will be AC 0.55kW.
*Reel lowering and lifting reducer will be yılmaz reducer.
*Reel lowering and lifting reducer will be yılmaz reducer.
*The bearings to be used will be SKF Brand original bearings with banderol.
*The pay-off drive motor will be AC 2.2kW.
*The AC motors to be used will be Wat, Elk or Gamak brand.
*Gradual pinhol is made according to the rollers to be used.
*Cable diameter: Ø18 mm
*Tape tray diameter: Ø350 mm
*Machine size (Width x Length x Height) mm: 960 x 2670 x 1920 mm
*Machine weight: 1100 kg
*Tray motor: 2.3 kW 1500 / 3000 rpm Servo motor
*Capstan motor: 2.3 kW 1500 / 3000 rpm Servo motor
*Capstan to gearbox conversion ratio I: 20
*Special design mechanism and lining group for mica tightness adjustment.
*Pulley diameter from pulley: Ø295 mm
*Number of pulley channels from the pulley: 6
*Accumulator pulley diameter: Ø260 mm
*Number of input accumulator fixed pulleys: 2 pcs
*Number of accumulator moving pulleys: 3 pcs
*Number of output accumulator fixed pulleys: 2 pcs
*Number of output accumulator moving pulleys: 3 pcs
*Input accumulator: Pneumatic piston stroke length 600 mm
*Output accumulator: Pneumatic piston stroke length 600 mm
*There is a regulator with indicator and adjustment for the inlet accumulator piston.
*There is a regulator with indicator and adjustment for the output accumulator piston.
*Volume of air storage tank for pneumatic pistons: 15 Liters
*Air storage tank material for pneumatic pistons: AISI 304L Stainless
*Air storage tank test pressure for pneumatic pistons: 9 bar
*Air storage tank test pressure for pneumatic pistons: 6 bar
*Pneumatic piston mounted input accumulator has linear potentiometer.
*Pneumatic piston mounted input accumulator with linear potentiometer
*Gas piston is used for the front and back cover opening towards the top.
*Concealed hinges and cover locks with lever locks are used for each cover.
*There is a section where the operator can store the necessary materials for materials and maintenance.
*Rotating materials and cable line are protected with containers.
*Designed according to CE machine safety regulations.
*Pinhole opening and closing will be automatic reducer motorised.
*Pinhole opening and closing motor shall be AC 0.25kW.
*Pinhole opening and closing reducer will be yılmaz reducer.
*Machine lowering and lifting will be automatic reducer motorised.
*Machine lowering lifting motor shall be AC 0.55kW.
*Machine lowering lifting reducer will be yılmaz reducer.
*Pinhol and the shafts to which it is connected shall be manufactured from 4140 material with heat treatment.
*The bearings to be used shall be SKF Brand original bearings with banderol.
*Toplayıcı tahrik moturu AC 2.2kW olacaktır.
*AC motors to be used will be Volt or Gamak brand.
*Staggered pinhol will be made according to the reels to be used.
*The travers motor will be a Servo Motor with a power of 0.75kW.
*Crawler screw shaft and nut ready Hiwin will be used.
*Corner turns will be adjustable from the screen.
*The router group will be made of rolls and pulleys.
*The machine will be controlled by operator panel.
*The screen will be 7” touch screen.
*Meter information, line speed information can be seen on the screen.
*Metre and line speed information will be controlled from encoder.
*Picker travelling step settings and turning points can be controlled from the screen.
*The turning points of the guide turns can be recorded instantly, so that the windings will be smooth in the changes of the reel sizes.
*The Transmitter will operate with lift control while the Collector is operating in speed mode.
*On the transmitter and collector legs, there will be lower-lift, open-close and emergency stop buttons.
*Corner turns will be secured with sensors, and there will be crawler termination sensors.
*Pinhole opening and closing levels shall be with safety sensor.
*Pinhole lowering and lifting levels shall be with safety sensors.
*The line will stop when the metre is full.
*When the meter is reset, the previous metre will be displayed on the screen.
*Capstan and banding tray motors will be servo motor.
*Banding tray motor and capstan can work synchronously.
*It has the capacity to make mica banding at high speed, 30m/min speeds.
*Machine voltage: 380V / 50 Hz / 3 PH
Product Catalogue
